Sony Blu Ray Player Universal Remote Codes

Table of Contents

Introduction

In this comprehensive guide, we will provide you with Sony Blu-ray player universal remote codes and step-by-step instructions on how to program your remote. Say goodbye to the hassle of searching for codes or dealing with complicated setups. Whether you have a 5-digit, 4-digit, or 3-digit code, we’ve got you covered.

Sony Blu-ray Disc Player Universal 5 Digit Codes

Here are the 5-digit codes you can use to program your Sony Blu-ray player remote:

11516
41516
42178
42180

Sony Blu-ray Disc Player Universal 4 Digit Codes

If you have a 4-digit remote code, choose from the following list:

2484
1516
2014
2020
2022
2065
2103
2108
2113
2162
2171
2176
2189
2203
2226
2238
2244
2251
2257
2273
2278
2296
2298
2305
2306
2307
2309
2313
2329
2332
2338
2355
2405
2406
2407

Sony Blu-ray Disc Player Universal 3 Digit Codes

For those with 3-digit codes, try the following:

GE Universal Remote Codes For Sony Blu-Ray Player

If you happen to have a GE universal remote, these codes will work for your Sony Blu-Ray player:

0707
0792
0794
0800

How to Program Sony Blu-Ray Universal Remote Without Codes?

Programming your Sony Blu-Ray universal remote without codes is a breeze. Follow these simple steps:

Switch On: Turn on the device you want the universal remote to operate, such as your TV.
Activate the Remote: Tap and hold the device button (e.g., TV, DVD, CBL, OK/SEL) on the remote for 3 seconds. The LED light will indicate that the device is ready to be programmed.
Pair with Your Device: Point the remote at your device and click the “CH+” and “CH-” buttons. The remote will send on/off signals. Keep pressing the “up” or “down” key until your device turns off.
Test the Code: Verify the code by clicking the “power” key. If your device powers on, try changing the channel to ensure the remote is correctly programmed.
Save the Code: Tap the “device” button to save the code. The LED on the device will blink twice to confirm that the code has been stored.

How to Program Sony Blu-Ray Universal Remote With Manual Method

If you prefer a manual approach, follow these steps:

Turn On the Device: Start by turning on the device you want to program with the remote.
Select TV: Press the “TV” button on your Sony Blu-Ray universal remote.
Enter Learning Mode: Press and hold the “Setup” button on the remote until it flashes.
Enter Keycode: Enter the keycode from the programming guide (instructions booklet) that corresponds to your device.
Pair with TV: Point your remote at the TV and hold the “Power” button. Release it when the screen turns off.
Test Functionality: Make sure your TV responds to the remote’s commands. If not, repeat the procedure with a different code from the reference table.

How to Program Sony Blu-Ray Universal Remote With Code Search

If you can’t find the right code, try the code search method:

Power On: Turn on the device you want to program.
Setup: Press and hold the “Setup” button on the remote.
Enter Code: Enter the code “9-9-1” (three digits).
Search Mode: Continue holding the “Setup” button and press the “Power” button. Then, press the “Channel Up” button repeatedly until your device, in this case, your TV, turns off.

This method may take a bit more time, but it’s essential to find the correct code for your device. Once complete, your remote should work flawlessly for all functions.

Conclusion

If you found this article helpful, please provide feedback to help us improve our site and assist others looking for remote codes. We also welcome new universal remote control codes that have worked for you. Share them in the comment section below, and we’ll post them on our site for the benefit of others. Say goodbye to remote control woes and enjoy seamless entertainment with your Sony Blu-Ray player.